Showing 25–30 of 30 results
-
Sale!
R150.00 R120.00 Incl. Vat
MADE IN GERMANY
Zenit Flex Stripe abrasive and polishing stripe is used for finishing and polishing the surface of the restoration. It is made of Aluminium oxide layer and polyester. Easy to snatch.
-
Sale!
R130.00 R120.00 Incl. Vat
MADE IN GERMANY
Zenit Flex Stripes prevent the generation of interteeth plaques and assists to obtain high quality finishing and polishing process.
* The single side of the stripe is covered with aliminium oxide
* Super thin disc can easily reach the desired area of the tooth and idel fort he inter-teeth polishing.
* Easy to use because of color coding
-
Sale!
R450.00 R350.00 Incl. Vat
MADE IN GERMANY
Light curing nano ceramic composite with outstanding physical properties and optimized handling for direct restorations of all cavity classes as well as indirect restorations such as inlays and onlays. Nanotechnology has been proven in the chewing simulator…
The high load resistance of ZENIT has been proven in the chewing simulator at the München University dental clinic. The abrasion with pressure load and shearing force was significantly less than that of comparable material.
-
Sale!
R5,000.00 R2,999.00 Incl. Vat
MADE IN GERMANY
Nano Composite is a composite that can be cured with light and polished with high brightness. It includes ultra-thin radio-opaque porcelain filling that is used for the treatment of adhesive filling. It can be polished with high brightness.
Thanks to its ultra-thin particle filling there can be made homogeneous restorations. Chameleon effect enable the composite to perfectly adapt to the structure of the teeth. It is compatible with DIN EN ISO 24 049 Zenit Nano Ceramic Composite is presented in easy to use syringe.
-
R999.00 Incl. Vat
MADE IN GERMANY
Indications
Permanent adhesive luting of indirect restorations (inlays, onlays, crowns, bridges, endodontic posts) made of nobel metal, non-noble metal, PFM | Zirconia, glass ceramic (crowns and bridges) | Fiber reinforced composite (endodontic posts).
Charecteristics
– Self adhesive
– High bond strength on enamel, dentin, metal and ceramics
– Radiopaque
– Dual-cure
– High mechanical properties
Application
1. Remove the temporary restoration and carefully clean off any residual temporary luting cement from the cavity or prepared core. Rinse with a water spray. Dry using oil-free air, avoid over drying the dentine.
2. Verify the accuracy of the fit of the restoration.
3. Then clean the restoration thoroughly and pretreat as follows:
Etchable glass ceramic:
Etch the restoration with 5% hydrofluoricacid in accordance with the manufacturer’s instructions, rinse thoroughly using a water spray and dry using oil-free air, apply silane (e.g. SilanePrimer) in accordance with the manufacturer’s instructions.
Oxide ceramics, metal sand metal alloys:
Pre-treat in accordance with the manufacturer’s instructions. Unless otherwise stated, sand blast the inside of the restoration with aluminumoxide (< 50 μm), clean with alcohol, and dry with
air that is free of oil and water.
Fiber-reinforced root posts:
Clean the root post with ethanol, dry with oil-freeair, and apply saline (e.g. Saline Primer) in accordance with the manufacturer’s instructions.
Product Code / Package Details
• PRD.ZCEM.TRS Transparent 1x 5ml (9.6gr) + 10x Applicator Tips
-
R10,500.00 Incl. Vat
Introduction
“Zenolite” Curing Light from President Dental “Zenolite”, is designed and manufactured by the advanced technology of
President Dental Germany. Its superior performance and an ergonomic design will provide dentists with convenience in treatment.
Main Features
– Maximum Output 2,700 mW/cm² (±10 %)
– Excellent readability through the OLED display
– Multifarious modes for convenient access
– Use interchangeable battery pack
– Use interchangeable light probe rotated a full 360 decrees
– Cordless system (use lithium- Ion battery)
Mode Description
Standard mode
1) Optical output – Over 900 mW/cm² (±10%)
2) Available time setting – 5, 10, 15, 20 seconds
High mode
1) Optical output – Over 1,300 mW/cm² (±10%)
2) Available time setting – 3, 6, 9, 12 seconds
Soft start mode
1) Optical output – After gradually increasing from 0 to 1,300 mW/cm² (±10%) and be maintained until finish time
2) Available time setting – 3, 6, 9, 12 seconds
Orthodontic mode
1) Optical output – Over 1800 mW/cm² (±10%)
2) Available time setting – 3, 4, 5 seconds
Xtra mode
1) Optical output – Over 2700 mW/cm² (±10%)
2) Available time setting – 1, 2, 3 seconds
